Products

  1. Home
  2. Products
  3. DC DC Power Module
  4. DC DC 1W
  5. 5V to 15V 1W 67mA DC to DC 80% transfer input power module replace HLK-1D0515
  • j

5V to 15V 1W 67mA DC to DC 80% transfer input power module replace HLK-1D0515

  • Visitor
    491
  • Buycount:
  • Price
    $1.25

产品型号-3-copy-0


Product Feature

1. characteristic:Constant voltage input, isolated non stabilized voltage single output,1W 

2. transfer efficiency 80%(Typ) 

3. Isolation is required between input and output(isolation voltage≤1500VDC) 

4. output short-circuit protection 

5. The voltage of the input power supply is relatively stable.(Voltage variation range±10%Vin) 

6. operating temperature range :-40°C~+85°C 

7. The stability of output voltage is not required. 

8. Small SIP package 

9. International standard pin,direct installation of PCB board. 

10. Adopts high quality environmental protection, waterproof and heat conducting adhesive for filling and sealing, moisture-proof and vibration proof, meeting the waterproof and dustproof IP65 standard 

11. High reliability and long life design,continuous working time MTBF≥3.5 million hours (3500000Hrs)


Enviroment Condition

Project nameQualificationUnitNotes
Working enviroment temperature-40—+85
Storage temperture-40—+80 ℃
Relative humidity5—95%
Heat dissipation modenatural cooling

Atmospheric pressure80—106 KpaKpa
VibrateVibration coefficient 10~500Hz,2G10min./1cycle, 60min.each along X,Y,Z axes
Meet the requirements of secondary road transportation


Input Characteristics

Project nameWorking conditionsUnitNotes
Related input voltage5Vdc
Input voltage range4.5-5.5Vdc
Maximum input current≤0.3A
Reflection ripple current15mA

DC5V rated input voltage series

Impulse voltage≤9Vdc
Starting voltage4.5Vdc
Input undervoltage protection---Vdc
Start-up delay---msRated input voltage and costant resistance load
Input filter type
Capacitance filter type
Hot plugged
Non-support



Output Characteristics(15v/200mA)

Project nameTechnical requirementUnitNotes
No load rated output voltage15V±15%Vdc
Short-time maximum output current≥77mA
Rated output current67mA
Voltage regulation±1.5%
Load regulation ±6%
Transfer efficiency Vin=5Vdc, output full load 80%
Output grain sweep noise(mVp-p)Pure resistance load, 20MHz bandwidth, peak to peak valuemV
Output over-voltage protection
Outputting the maximum voltage 110-160%Vdc
Insulation voltageInput- output, test in 1 minute, leakage current less than 1mA/1500V-
Insulation resisitanceInput- output, insulation volaltge 500VDC/1000MΩ
Isolation capacitanceInput- output, 100KHz/0.1V 20pF-


Note:

1、The above is only a list of typical products. If you need products beyond the list, please contact our sales. 2、The maximum capacitive load indicates the maximum capacitive load that + VO or - vo can be connected to,If the value is exceeded, the product will not start normally..


Typical Application Circuits

image

EMC parameter recommendation


Component No.FunctionRecommended value
 Cin CapacitanceFilter capacitor4.7μA/50V
Cout CapacitanceFilter capacitor2.2-10μA/50V
Lin inductanceFilter inductanceInductance: 4.7uH
Lout inductanceCin CapacitanceInductance: 4.7uH

Notes:Output Load Requirements 

In order to ensure that the module can work efficiently and reliably, the minimum output load should not be less than 10% of the rated load.If the power you need is really small, please connect a resistor in parallel between the positive and negative poles of the output terminal (the sum of the actual power used by the resistor is greater than or equal to 10% of the rated power and the rated power of the selected resistor must be greater than 5 times of the actual power used, otherwise the temperature of the resistor will be higher)



© 2021 Shenzhen Hi-Link Electronic Co., Ltd. All Rights Reserved.